[llvm-commits] [llvm] r164805 - /llvm/trunk/docs/HowToBuildOnARM.rst

[Micah Villmow]

Author: villmow
Date: Thu Sep 27 17:14:10 2012
New Revision: 164805

URL: http://llvm.org/viewvc/llvm-project?rev=164805&view=rev
Log:
Fix more crlf issues.

Modified:
    llvm/trunk/docs/HowToBuildOnARM.rst

Modified: llvm/trunk/docs/HowToBuildOnARM.rst
URL: http://llvm.org/viewvc/llvm-project/llvm/trunk/docs/HowToBuildOnARM.rst?rev=164805&r1=164804&r2=164805&view=diff
==============================================================================
--- llvm/trunk/docs/HowToBuildOnARM.rst (original)
+++ llvm/trunk/docs/HowToBuildOnARM.rst Thu Sep 27 17:14:10 2012
@@ -1,34 +1,34 @@
-.. _how_to_build_on_arm:
-
-===================================================================
-How To Build On ARM
-===================================================================
-
-.. sectionauthor:: Wei-Ren Chen (陳韋任) <chenwj at iis.sinica.edu.tw>
-
-Introduction
-============
-
-This document contains information about building/testing LLVM and
-Clang on ARM.
-
-Notes On Building LLVM/Clang on ARM
-=====================================
-Here are some notes on building/testing LLVM/Clang on ARM. Note that
-ARM encompasses a wide variety of CPUs; this advice is primarily based
-on the ARMv6 and ARMv7 architectures and may be inapplicable to older chips.
-
-#. If you are building LLVM/Clang on an ARM board with 1G of memory or less,
-   please use ``gold`` rather then GNU ``ld``.
-   Building LLVM/Clang with ``--enable-optimized``
-   is prefered since it consumes less memory. Otherwise, the building
-   process will very likely fail due to insufficient memory. In any
-   case it is probably a good idea to set up a swap partition.
-
-#. If you want to run ``make
-   check-all`` after building LLVM/Clang, to avoid false alarms (eg, ARCMT
-   failure) please use the following configuration:
-
-   .. code-block:: bash
-
-     $ ../$LLVM_SRC_DIR/configure --with-abi=aapcs
+.. _how_to_build_on_arm:
+
+===================================================================
+How To Build On ARM
+===================================================================
+
+.. sectionauthor:: Wei-Ren Chen (陳韋任) <chenwj at iis.sinica.edu.tw>
+
+Introduction
+============
+
+This document contains information about building/testing LLVM and
+Clang on ARM.
+
+Notes On Building LLVM/Clang on ARM
+=====================================
+Here are some notes on building/testing LLVM/Clang on ARM. Note that
+ARM encompasses a wide variety of CPUs; this advice is primarily based
+on the ARMv6 and ARMv7 architectures and may be inapplicable to older chips.
+
+#. If you are building LLVM/Clang on an ARM board with 1G of memory or less,
+   please use ``gold`` rather then GNU ``ld``.
+   Building LLVM/Clang with ``--enable-optimized``
+   is prefered since it consumes less memory. Otherwise, the building
+   process will very likely fail due to insufficient memory. In any
+   case it is probably a good idea to set up a swap partition.
+
+#. If you want to run ``make
+   check-all`` after building LLVM/Clang, to avoid false alarms (eg, ARCMT
+   failure) please use the following configuration:
+
+   .. code-block:: bash
+
+     $ ../$LLVM_SRC_DIR/configure --with-abi=aapcs