[LLVMdev] SLP vectorizer on AVX feature

[Frank Winter]

I realized that the function parameters had no alignment attributes on 
them. However, even adding an alignment suitable for aligned loads on 
YMM, i.e. 32 bytes, didn't convince the vectorizer to use [8 x float].

define void @main(i64 %lo, i64 %hi, float* noalias align 32 %arg0, 
float* noalias align 32 %arg1, float* noalias align 32 %arg2) {
...

results still in code using only [4 x float].

Thanks,
Frank


On 07/01/2015 10:51 AM, Frank Winter wrote:
> I seem to have problem to get the SLP vectorizer to make use of the 
> full 8 floats available in a SIMD vector on a Sandy Bridge CPU with 
> AVX. The function is attached, the CPU flags are:
>
> flags        : fpu vme de pse tsc msr pae mce cx8 apic mtrr pge mca 
> cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall 
> nx pdpe1gb rdtscp lm constant_tsc arch_perfmon pebs bts rep_good 
> xtopology nonstop_tsc aperfmperf pni pclmulqdq dtes64 monitor ds_cpl 
> vmx smx est tm2 ssse3 cx16 xtpr pdcm dca sse4_1 sse4_2 x2apic popcnt 
> aes xsave avx lahf_lm ida arat epb xsaveopt pln pts dts tpr_shadow 
> vnmi flexpriority ept vpid
>
> I use LLVM 3.6 checked out yesterday
>
> ~/toolchain/install/llvm-3.6/bin/opt -datalayout -basicaa 
> -slp-vectorizer -instcombine < func_4x4x4_scalar_p_scalar.ll -S
>
> the output goes like:
>
> ; ModuleID = '<stdin>'
>
> define void @main(i64 %lo, i64 %hi, float* noalias %arg0, float* 
> noalias %arg1, float* noalias %arg2) {
> entrypoint:
>   %0 = bitcast float* %arg1 to <4 x float>*
>   %1 = load <4 x float>* %0, align 4
>   %2 = bitcast float* %arg2 to <4 x float>*
>   %3 = load <4 x float>* %2, align 4
>   %4 = fadd <4 x float> %3, %1
>   %5 = bitcast float* %arg0 to <4 x float>*
>   store <4 x float> %4, <4 x float>* %5, align 4
> ....
>
> So, it could make use of <8 x float> available in that machine. But it 
> doesn't. Then I thought, that maybe the YMM registers get used when 
> lowering the IR to machine code. However, the generated assembly 
> doesn't seem to support this assumption :-(
>
>
> main:
>     .cfi_startproc
>     xorl    %eax, %eax
>     xorl    %esi, %esi
>     .align    16, 0x90
> .LBB0_1:
>     vmovups    (%r8,%rax), %xmm0
>     vaddps    (%rcx,%rax), %xmm0, %xmm0
>     vmovups    %xmm0, (%rdx,%rax)
>     addq    $4, %rsi
>     addq    $16, %rax
>     cmpq    $61, %rsi
>     jb    .LBB0_1
>     retq
>
> I played with -mcpu and -march switches without success. In any case, 
> the target architecture should be detected with the -datalayout pass, 
> right?
>
> Any idea what I am missing?
>
> Frank
>
>
>
> _______________________________________________
> LLVM Developers mailing list
> LLVMdev at cs.uiuc.edu         http://llvm.cs.uiuc.edu
> http://lists.cs.uiuc.edu/mailman/listinfo/llvmdev